Thanks to the gear sensors, TITAN II Bluetooth® precisely detects where the cycle ends. So, even the shortest trigger action produces at least one full cycle. Two optical sector gear sensors count each tooth of the gear as well as the direction of the rotation, making it possible to use a broad range of gears: DSG, SSG, 19-tooth, and standard ones. You can select the cycle manually.

Cycle detection gives you

AUTOMATIC BURST

You don't need to set the burst time—you can set the burst between 2 and 99 shots

AUTOMATIC Pre-Cocking

Pre-Cocking is fully operational in SEMI, BURST, and AUTO modes and there's no need to set the Pre-Cocking boost manually; you can simply set Pre-Cocking from 0-5

FULL CYCLE

When Pre-Cocking is off, TITAN II Bluetooth® ensures that the gearbox completes a full cycle and you gain more reliability

With a new generation of dual gear sensor, TITAN II Bluetooth® has the most accurate cycle control ever developed. Our sensor allows detection of every tooth on the gear and the direction of rotation.

Adjust the motor’s braking power according to your needs. Choose breaking value manually or set the Adaptive Active Brake. It will stop the piston in the front position, which eliminates unnecessary stresses, increasing the service life of the gearbox and its parts.

Adaptive Active Brake – automatically adjusts the motor’s braking power according to the setup of your replica.

Manual Active Brake – choose your own value between 0-100% of Active Brake depending on your needs.

Victory in the game is often a matter of fractions of seconds. Thanks to pre-cocking, you gain trigger reaction similar to real life. This allows for initial spring compression, which speeds up trigger response significantly.

There are two Pre–Cocking Modes:

1. AUTO Mode – the spring is automatically compressed after each shot–you choose the level of Pre–Cocking from 0-5
2. MANUAL Mode – set the Pre–Cocking values yourself–instead of levels there are time settings, you have to choose the time for yourself by trial and error

Please note: using Pre–Cocking increases wear and tear on the gearbox.

You don't need to fully release the trigger to fire the next shot. This option is really useful when the trigger sensitivity level is very high. Choose between

• OFF - to fire the next shot, you need to release the trigger until it reaches the selected trigger sensitivity level.
• 2LVL - to fire the next shot, just release the trigger until it moves over two adjoining sensors.
• 1LVL - to fire the next shot, just release the trigger until it moves over an adjoining sensor.

Update your firmware with the GCS app – apply changes, make improvements, and get bugfixes.

Tournament Lock allows you to lock your settings for a predefined amount of time. TITAN II Bluetooth® is great for events where precision and a level playing field are necessary.

This feature allows you to troubleshoot your replica in case of any issue. Errors are communicated once they occur, and their description can be found in the GCS App.

Direct Bluetooth® connection with your GCS app allows you to configure your TITAN II Bluetooth® in a matter of seconds using just your phone.

Enables you to set two different trigger sensitivities. Pulling the trigger slightly produces SEMI or BURST fire. Pulling it further produces BURST or AUTO fire. Select your sensitivity preferences for each stage.

We know how vital fast trigger response during combat is. That's why we've developed the Smart Trigger function, which enables you to achieve faster trigger response. It works with the ROF Control System. During the first shot, the microprocessor sets the ROF control to 100%. After the first shot, it switches to a previously programmed value (e.g. 50%). As a consequence, the first shot is fired at a full ROF and subsequent shots at a reduced ROF. The best results can be achieved when using a battery with above standard voltage. For example, if you’re using a 7.4 V battery, you can replace it with a 11.1 V one. This way, you will achieve faster trigger response with the same rate of fire than with a standard battery. 

Two selector sensors allow you to take advantage of 343 selector mode variations. The following modes are available for selection:

SAFE – prevents your replica from firing, even if the safety lever is removed

SEMI – fire one shot per one trigger pull

BINARY – one shot on the trigger pull and another shot upon release 

BURST – shoot a predetermined number of BBs, which is very useful in MilSims and when using low-caps; there are 2 BURST Modes available: 

• Full – a burst is shot in full, even if the trigger is released before the preset number of BBs has been shot
• Interruptible – the burst can be interrupted by releasing the trigger earlier – even if not all the BBs from the burst have been shot the replica stops firing once the trigger has been released

BURST/AUTO – available in Full BURST Mode only; allows for extending a burst by any number of shots – if you hold the trigger after the burst is shot, it switches to AUTO Mode 

AUTO – shots are fired as long as the trigger is pulled

SEMI RAMPING – if you pull the trigger very fast, it switches to AUTO Mode

Please note: In the case of Regional Lock, only SEMI Mode is available. Check law restrictions in your country.

External accessories such as Bolt-Catch sensor can be used as a trigger and selector thanks to the Multifunctional Port in your TITAN II Bluetooth®. Connect, set them in the GCS app and you’re good to go!

Enables to set a predefined BB number fired in a single series. It can be used as protection against trigger jams. In case of emergency, you can stop the series by switching the selector position.

Simulated magazine capacity and magazine reload allows you to set the magazine capacity and the time between reloads, allowing you to use a MID-CAP magazine and maintain realism by limiting the capacity, for example, to 30 shots, and setting a pause in shooting for a few seconds, simulating a magazine change. You can set between 1-250 BBs.

ROF Control reduces your replica’s rate of fire. Allows you to use stronger batteries and still have the ROF exactly as you like. You can choose between

Adaptive – set your desired rate of fire; the brake and delay will be automatically adjusted to achieve this value

Manual PWM – set the motor power throughout the duration of the shot

Manual Delay – set the exact delay between shots in milliseconds

Manual Delay + PWM – set braking power and delay manually

This allows you to quickly check whether the drop-in module is working properly. It helps to locate where the problem lies when anything goes wrong.

Do you want to achieve a higher ROF and faster trigger response? Are you planning a power upgrade of your gun? In this case, you need a MOSFET.

It targets the energy from the battery directly to the motor, bypassing the mechanical trigger contacts. As a result, you gain a higher ROF of the gun and faster trigger response.

Thanks to its special conformal coating, our product is resistant to atmospheric conditions (Military Specification MIL-V-173C).

It lets you set the delay between shots or series to simulate the delay from reload or recoil. You can set the delay between 0.01-5 s for EXPERT firmware.

Protection against battery over-discharge. Modern LiPo and LiFe batteries are very sensitive to over-discharge. If you do not want to damage the battery and you care about its service life, this protection is indispensable. The microprocessor is constantly monitoring battery voltage. When voltage drops to a critical level, it will not allow firing. The number of battery cells can be detected automatically.

TITAN II Bluetooth® protects solenoid valves of your HPA enigne from faster wear and tear or permanent damage thanks to protection against nominal voltage over 7.4 V in connected batteries.